Superior SDVI User Manual

INSTALLER: Leave this manual with the appliance.CONSUMER: Retain this manual for future reference.INSTALLATEUR: Laissez cette notice avec l'ap

10Air Inlet Liner (for combustion air) When terminating the air inlet liner at this point, a positive flue connection is required (to ensure combustion

11NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Zero Clearance Fireplace InstallationThis insert may be installed in a masonry or factory built/

12NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Figure 10Surround Panels InstallationThe SDVI insert surround panels are made of heavy gage stee

13NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.These appliances must be isolated from the gas supply piping system (by closing their individual

14NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Moving shutter bracket to the right will open shutter, to the left will close shutter.Figure 14F

15NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.La chimenea caliente cau-sará quemaduras gravesNunca permita que los niños toquen el vidrio ni o

16NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Operating InstructionsPre-Lighting ChecklistBe sure to check these items before the initia

17NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.5. Locate the pilot by looking over the top of the left front log. A blue flame will be seen when

18NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Flame Color and BehaviorYour SDVI gas insert is designed for maximum heating efficiency. Therefor

19NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Operating OptionsThe rocker switch on your SDVI gas insert is used to turn the burner on and off

2CONGRATULATIONS!When you purchased your new gas fireplace insert, you joined the ranks of thousands of individuals whose answer to their home heating

20NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.CAUTION: Wear gloves and safety glasses for protection while doing required maintenance.Verify

21NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Glass DoorFigure 20(B) Door Mounting Plates(A) Spring Handle LatchesGlass Door RemovalTo remove

22NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Fuel ConversionConverting your SDVI gas insert between natural gas and LP can be accom-plished b

23SYMPTOM PROBABLE CAUSE CORRECTIVE ACTIONThin black coating (soot) forms on the viewing glass, logs, or fireboxImproper log or ember placementImproper

24Touch-Up Paint Kit70K99TSPK-BTouch-Up Paint, Metallic Black (12 oz aerosol)PAINTWallThermostatRemote ControlControlsCat. No. Model Description70005

25Arched FaceNOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.4 Gear clampsTerminationCapFlashingVent Kits H0909 FKDVI Flex Liner Kit, DVI 3” X 35’

26NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.MINIMUM CLEARANCES TO COMBUSTIBLESE = 31.5” (800mm) from Top Facing to Bottom of InsertF = 25.5”

27NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.CAUTION: YOUR SUPERIOR™ GAS APPLIANCE MUST ALWAYS BE OPERATED WITH GLASS DOOR IN PLACE. STOP! R

Printed in U.S.A. © 2008 LHPP/N 506056-01 REV. C 03/2010 LHP reserves the right to make changes at any time, without notice, in design, materials,

3IMPORTANT SAFETY AND WARNING INFORMATION WARNING Young children should be carefully supervised when they are in the same room as the appliance.

4FOR YOUR SAFETY do not install or operate this appliance without first reading and understanding this manual. Any installation or operation of the a

5Fireplace RequirementsThese heaters are designed to be installed into an existing masonry fireplace (built to UBC 37 or ULC S628 standards)

6Installation of these appliances are approved for installation in New York City in the US state of New York (MEA#: 138-07-E).(Massachusetts Approval

7FeaturesInstallation Options Residential - Vented Vertical Only Manufactured (Mobile) Home Natural Gas Or Propane (LP) Bedrooms Optional Wall-

8NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Insert DimensionsMinimum Fireplace Opening RequiredA = 31-1/4” (794mm) Front OpeningB = 17-1/

9NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Facing and MantelSide ViewFacing and Mantel ClearancesNote: Hearth protection to be min. 3/8” (10